How to Design and Size a Busbar

Rittal 31/01/2017

237 2 minutes read

Listen to this article

The introduction of the IEC 61439 switchgear and control standards has had significant implications for the design and performance of the copper busbar system.

It’s an area which design engineers need to appreciate, not least because the new testing regime and the requirement for compliance has changed the way we think about the selection of the busbar system.

There are a number of key factors relating to the design/layout stage of an assembly:

Where to put the busbar

The decision as to where to put the busbar depends on the location of the incoming cables and the position of the incoming protection device.

The form rating helps determine the layout of the assembly, the position of devices such as the circuit breaker, terminals and the busbar system, as well as whether the busbar requires a cover.

Ultimately, the size of the enclosure will be dependent upon both the form rating and the busbar system fitted.

Current rating

The total load has to be pre-calculated as this impacts on the size of the busbar. Consideration must also be given to the IEC 61439 standards because under certain circumstances it requires a rating of 125% of the full load current.

Knowing the current loadings means that watt loss can be calculated which will in turn have a direct impact on temperature rises within the enclosure. Again, this is a key element of the standard, along with the maximum temperature ratings.

Connections

Connecting conductors to the busbar can cause problems for contractors as any oversized cables may be too large to terminate on the busbar system.
Design engineers need to consider this possibility and compensate with different busbar adaptors or terminals.

But, remember that any additional copper connections may invalidate the busbar warranty as they could be considered to be extending its capability beyond the tested system.

Under the standard, all copper connections above 1600A have to be tested for impact of heat rise on the air circuit breaker. In addition, the connections from and to the main busbar system have to be physically tested by the original equipment manufacturer of the switchgear system. Essentially, the panel builder cannot make their own.

Fault ratings

High-fault currents (short-circuits) can obviously be highly destructive. The initial electro-mechanical force generated in fault conditions can be huge – tens of thousands amps.

As a consequence, the busbar system must be robust enough to carry the current until the short-circuit protection device (such as a fuse or MCCB) trips.

Design engineers have to be aware of the fault rating from the outset, a level that is determined by several factors: the size of the supply transformer; the impedance of cables from the transformer; and current limiting effects of the protection device.

The fault rating can be given as either a RMS kA – which typically has a time withstand value of one second – or a peak value measured in kA.

Instructions around how to install the busbar support are the responsibility of the original manufacturer of the switchgear system and issues such as the spacing of the busbar supports are determined by the manufacturer’s testing.

These distances are governed by the fault level and the size of the copper bar. They and their spacing (ie. how far they are apart) have a major bearing on the strength of the system; if the supports are fitted too close to each or too widely distant, then the system’s performance under fault conditions could be badly affected.

Further information at www.rittal.co.uk and www.friedhelm-loh-group.com or on twitter @rittal_ltd.

Contact Details About Us Latest News Latest Videos

Rittal Ltd

01709 704000
information@rittal.co.uk
http://www.rittal.co.uk
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY GB

About us

Since its foundation in 1961, Rittal has continuously evolved into the world"s leading systems provider for enclosures, power distribution, climate control, IT infrastructure and software & services.

Today, "Rittal – The System." offers you a perfectly coordinated system platform. It unites innovative productions, pioneering engineering solutions and global service to accommodate the most diverse requirements. It caters to a whole host of industries, from machinery and plant engineering, to the automotive industry, through to information technology.All from a single source, all in top quality.

That is what "Rittal – The System. Faster – better – worldwide." is all about.

A workforce of 10,000 manufactures and develops "Rittal – The System." on your behalf. Ensuring you stay on track for success. Tap into synergy potential with our sister company Eplan, the leading manufacturer of software for cross-disciplinary engineering solutions.We never lose sight of our responsibility to the environment and society.

Where we supply to

Europe, Africa, Asia, Australia, South America, North America

Industries we supply to

Automation, Chemicals, Consultants, Components Electronics, Energy and Power, Food and Beverage, Glass Ceramics Cement, Metals and Minerals, OEM, Paper and Pulp, Pharmaceutical Cosmetics Toiletries, Plastics and Rubber, Recycling, Textiles, Tobacco, Water and Wastewater

Make wire processing ten times faster with Rittal’s Wire Terminal WT C: The versatile solution for wire processing

Rittal’s Wire Terminal WT C5 and C10 machines offer fully automatic wiring processes that go one step further. The innovative...
Smart cooling unit solutions with sustainable DNA Rittal Blue e+ S Cooling Units

Rittal is expanding its smart cooling unit solutions by adding the new Blue e+ S range. Our latest generation of...
Temperature vs Equipment – Who will Win?

Every year, there is a battle of two forces. The immovable object comes upon the unstoppable force in a war...
Experience Rittal live!

There are only weeks to go until the 2022 Drives & Controls exhibition which is held at the NEC Birmingham from the 5th-7th...
Rittal celebrates the one-millionth VX25

2021 was a triple milestone for Rittal, the company celebrated the 60th anniversary of its founding, the 75th birthday of...
Designing a Switchboard for a Fishing Trawler

When NU-Design Limited, a marine electrical services business based in Peterhead, Aberdeenshire, Scotland needed help in the designing of a very...