Long-life Bredel hose pumps for thickened sludge help to make waste less wasteful

A Bredel hose pump replaces a faulty progressive cavity pump at Scheldestromen water board’s treatment plant in Zeeland

A Bredel peristaltic hose pump has shown the ideal qualities for transferring thickened sludge in the production of biogas for Scheldestromen water board (Waterschap Scheldestromen) in the Netherlands.

A Bredel 65 hose pump is transferring polymer-thickened sludge of 6 to 8% to tanks for fermentation at Scheldestromen water board’s treatment plant in Terneuzen, Zeeland.

A progressive cavity pump was proving too costly with a short lifetime for transferring sludge, lasting two and a half months on average for a stator and stator rotor, which resulted in maintenance downtime.

Dimitry Loof, Work Planner at Scheldestromen water board, said: “It was a consideration between costs and benefits to change pumps, and also a short service life of the progressive cavity pump. We wanted to extend the service life of the pump for this application.”

Over the course of the three months, the progressive cavity pump’s capacity continued to decline. This meant Scheldestromen water board had to speed up the progressive cavity pump to be able to use the same flow rate.

When the pump was running at the end of its range, Scheldestromen water board could no longer absorb fluctuations in the process, resulting in a failure and a backlog in its total sludge processing. flow.

Lower costs thanks to a longer lifespan

The progressive cavity pump suffered a lot of wear in the stator and rotor due to sand, which caused pressure loss and the capacity to decrease. To replace a stator and stator rotor cost Scheldestromen water board a total of 3,000 euros (excl. VAT), as well as the time it took staff to do the pump maintenance.

Scheldestromen water board had to replace the stator and rotor with the progressive cavity pump three or four times per year.

Gertjan Dijkers, Process Operator at Scheldestromen water board, said: “The progressive cavity pump’s problems were largely caused by sand and the pressure pipe that was too small. The pressure pipe had a relatively high resistance. This was partly due to the long distance, a number of right-angle bends in the pipe and a relatively small cross-section of the pressure pipe (100 mm). This, in combination with a dry matter content between 6% and 8% (sludge and sand), ensured that the pump had a high back pressure. This caused the pump to wear out quickly.”

Due to the unreliable operation of the progressive cavity pump, Scheldestromen water board could not be certain it could process all the sludge supplied from the treatment plants.

Looking for a better performing pump with a longer service life, Scheldestromen water board met with Watson-Marlow Fluid Technology Solutions (WMFTS) to explore how Bredel hose pumps could be a solution. They also contacted another peristaltic pump supplier, a lobe pump manufacturer and a progressive cavity pump manufacturer.

Gertjan Dijkers, Process Operator at Scheldestromen water board, said: “We just wanted to be able to run for at least three months with the flow rate that we have to run. We have found that a Bredel hose pump can run for over three months before its capacity starts to decrease. The biggest advantage is that the hose pump simply does what it is supposed to do for over three months.”

Bredel hose pumps have no rotating parts to clog or wear with the sand, which considerably reduces maintenance and labour costs. As well as costs, the Bredel hose pump brings ergonomic benefits. Scheldestromen water board did not have to increase the diameter of the piping, which built up too much with the progressive cavity pump. The accessibility of the pump is much better with the Bredel, and because of the suction capability of the Bredel it is located on the ground floor.

Scheldestromen water board calculated it can have a return on investment on the Bredel pump in four years and make savings considerable savings on maintenance compared to the previous progressive cavity pump.

Maintenance costs and labour costs of the progressive cavity pump per year (average taken over six years) were 9,420 euros, according to Scheldestromen water board. Scheldestromen water board calculated it will make 42% savings in annual maintenance costs with the Bredel hose pump, compared to the previous progressive cavity pump. Another benefit for Scheldestromen water board is that a single operator can now change the pump hose without another co-worker’s assistance.

Ed Zorg, Industrial Sales Engineer for WMFTS in Netherlands, said: “Scheldestromen water board chose the Bredel pump for a few reasons. The other options were not a solution. The lobe pump had difficulty delivering high pressures above 4 bar, and the parts would wear out. The other manufacturer of peristaltic pumps did not have a pump available with the right size for this application as a test setup.”

“Another important reason why Scheldestromen water board chose us was the relationship we developed with them. We were able to quickly provide a demonstration pump from our Bredel factory, so they could look at it, and then we were able to make some tweaks to the pump for them before delivering it. That collaboration and quick response for a demo pump was important.”

Biogas production

Biogas produced by the fermented sludge is burned by the treatment plant’s own combined heat and power plant. As a result, 80% of the treatment plant is supplied with self-generated electricity.

The fermented sludge is processed into solid digestate and then burned. As the Bredel can pump more thickened sludge than the progressive cavity pump, Scheldestromen water board can now produce more biogas.

Dimitry Loof, Work Planner at Scheldestromen water board, said: “If we ran into problems due to the progressive cavity pump, we were forced to change to slow down the thickening process and thicken below 5% dry matter, which could jeopardise the entire process. If we pumped too little dry matter to the fermentation tank, the residence time in the fermentation tank was shorter. “

“We want the organic matter to be broken down as much as possible, and that requires a longer residence time. The disadvantage of a shorter residence time in the fermentation was that we also produced less biogas. And because of the limited operational reliability of the progressive cavity pump, the maintenance costs were also higher than normal.”

“With the Bredel we can run higher dry substances on the belt thickener and we can even send a higher flow rate to the belt thickener.”

“With the Bredel we don’t run with a little lower in dry substance, we just stay high, which is also an advantage. When you put higher dry matter into your fermentation tank, it results in better fermentation. The more water you put into fermentation tanks, the more you must heat. The drier the dry matter content, the less water you have to heat. This means it costs less energy to heat the fermentation tank. In the summer this problem does not occur, but in the winter you save a lot of energy because you have to heat less, so that is a big advantage.”

Further information can be found at www.wmfts.com

Contact Details About Us Latest News Latest Videos

Watson-Marlow Fluid Technology Solutions

• 01326370370
• info@wmftg.co.uk
• https://www.wmfts.com/
• Bicklandwater Road, Falmouth Business Park, Falmouth, Cornwall, TR11 4RU GB
Facebook Twitter Instagram

About us

Watson-Marlow Fluid Technology Group (WMFTG) peristaltic tube and hose pumps meet requirements including: value for money; low cost of ownership; reliability and ease of maintenance to the food and beverage, chemical, pharmaceutical, mining and many other industries.

We demonstrate how pumps deliver significant process efficiencies over the lifetime of the equipment. Whether performing flavouring addition in food processing, chemical metering in water treatment or mineral recovery, we have a solution which can cut pump downtime and reduce costs through higher accuracy metering and transfer. WMFTG has dedicated application engineers available to help customers make the right pump and tubing choice from a range providing microlitres per minute to 80 cubic metres per hour flow rates.

The only part of the pump to come into contact with the product is the tube or hose. This means there are no seals or valves that can wear or fail. Replacing the tube or hose can be performed quickly and safely. Peristaltic pump benefits include:

Total fluid containment with no seals No ancillaries Handle viscous and abrasive slurries and sludge Self-priming capability Dry running without damage to the pump In addition to their range of positive displacement pumps, Watson-Marlow Fluid Technology Group has added PTFE-lined chemical and industrial hoses to their range. Aflex hoses are reinforced to withstand the most severe conditions and use.

Where we supply to

Europe, Africa, Asia, Australia, South America, North America

Industries we supply to

Automation, Chemicals, Consultants, Components Electronics, Energy and Power, Food and Beverage, Glass Ceramics Cement, Metals and Minerals, OEM, Paper and Pulp, Pharmaceutical Cosmetics Toiletries, Plastics and Rubber, Recycling, Textiles, Tobacco, Water and Wastewater

• 

  Watson-Marlow to showcase Bredel CIP pump and next-generation fluid handling at PPMA 2025

  Watson-Marlow Fluid Technology Solutions (WMFTS) will unveil the latest Bredel CIP pump and its portfolio of next-generation fluid management technologies...

• 

  Watson-Marlow launches new Bredel CIP pump for beverage producers at drinktec

  Watson-Marlow Fluid Technology Solutions (WMFTS) is launching its latest innovation for the brew and beverage market; the Bredel CIP pump,...

• 

  Bredel Hose Pump Solves Ash Slurry Problem at Biomass Plant

  A Bredel 100 hose pump with an NR Transfer hose has been installed at a biomass power station in Pécs,...

• 

  Watson-Marlow Fluid Technology Solutions introduces WMArchitect Interchangeable Parts for robust single-use assemblies

  Watson-Marlow Fluid Technology Solutions (WMFTS) has introduced WMArchitect Interchangeable Parts to improve the longevity of single-use assemblies. The introduction brings...

• 

  Watson-Marlow to Exhibit Peristaltic Pump and Fluid Path Technologies in London Biotechnology Show Debut

  Watson-Marlow to Exhibit Peristaltic Pump and Fluid Path Technologies in London Biotechnology Show Debut Watson-Marlow Fluid Technology Solutions (WMFTS) will...

• 

  German Waste-to-Energy Plant Prolongs Hose Life Using Bredel NR Transfer Hoses

  Abfallverbrennungs- und Biokompost GmbH (AVBKG), the German waste processing plant, has achieved significant hose maintenance and hose life savings. Based...

• Flexicon PF7 tabletop peristaltic liquid filling machine

• Sterile ReNu SU Technology cartridge

• Quantum and ReNu SU Technology cartridge - Make sterile connections in non-sterile environments