Industrial Enclosure Air Cooling Solutions vs Liquid Cooling Solutions
By Karl Lycett – Rittal UK’s Product Manager for Climate Control
Almost without exception, industrial environments are hostile spaces for electrical equipment; their components don’t react well to high levels of moisture, dust, and heat in the atmosphere. This sensitivity, in turn, affects plant efficiency and will ultimately lower output and profitability.
But moisture, dust and heat don’t need to be a concern provided you implement an effective climate control solution for your equipment.
The first step is to consider what constitutes suitable cooling to meet your needs, bearing in mind that your cooling needs may alter with any future changes to applications within your facility.
It’s common for managers, when choosing a cooling solution, to default to air cooling using fans and filters because it’s familiar.
While air cooling can be a viable solution, it also has its limitations which must be understood before it’s installed, otherwise you risk creating further problems further down the line.
Air Cooling
Air cooling is relatively self-explanatory. The cooling is achieved by passing cooler, outside air across the enclosure’s warmer internal components. However, this simplicity has its shortcomings which should be kept in mind.
If at any point the temperature within the facility exceeds the maximum allowable temperature (setpoint) inside of the enclosure, then no cooling will be possible. A good example of this is during the height of summer when the combination of lots of machinery and high ambient temperatures can cause severe temperature spikes within the factory. These will quickly lead to overheating componentry and unexpected tripping of critical equipment. But this is only an issue if your factory is prone to surges in temperature. For many organisations, there is an acceptable level of general HVAC installed to ‘take the edge’ off the temperature, allowing air cooling to create a protective environment for the equipment within the enclosures.
Dust is a constant irritant within a factory and realistically it can never be fully removed. Even ‘cleanest’ industrial space will have a base level of detritus within the air which will then be drawn into enclosures if fans are employed. Unfortunately, this dust can get into wire connections or internal component fans and cause havoc over time, either preventing thermal exchange or blocking up and shorting wiring connections.
The best way to prevent dust issues arising is to add a suitable filter medium to your air cooling. Filter mediums (or mats) ‘catch’ particulates before they enter the enclosure. The mats should be replaced on a regular basis to prevent a build-up of dirt which can then ‘choke’ the fan, preventing it from pulling sufficient cooling air into the enclosure.
Liquid Cooling
As mentioned earlier, it’s common to find traditional air-cooling methods are unviable or simply not especially effective in industrial spaces. This can be due to factors such as the location or amount of the equipment involved, or it can be down to physical space restrictions,
Liquid cooling, however, is an option open to all, and one that is much more effective than air at removing waste heat and reducing the temperature within the enclosure.
Liquid cooling, as the name suggests, uses chilled water to perform the cooling of the enclosure. An ‘Air to Air Heat Exchanger’ is mounted on the enclosure and connected to an industrial chiller. The chiller cools down heated water from the enclosure to a reasonable temperature before delivering it back to the heat exchanger.
The beauty of liquid cooling is that it is ‘active’ which means that you can make the internal temperature lower than that of the local environment. So even in the height of summer, with the factory in full swing, your electrical equipment will be protected. Many industrial sites already have an operational chilled water supply to service other procedures and equipment. Where this is the case, it can be tapped off and used for enclosure cooling.
Liquid cooling requires hydraulic hoses (cold water in, hot water out) to be connected between the heat exchanger and the chiller. It’s therefore worth giving prior thought to both the enclosure placement and where to run the hoses to ensure the smooth commissioning and operation of the whole system.
Much like the air cooling, regular maintenance of the system is strongly recommended to ensure the cooling equipment can provide years of uninterrupted service.
In summary, both solutions are valid in the right scenario. However, choosing a cooling solution without first considering its operating environment is setting yourself up for less than perfect result. This in turn will have an impact on the overall effectiveness of your chosen cooling solution and the ongoing protection of your critical electrical equipment.
Further information at www.rittal.co.uk and www.friedhelm-loh-group.com or on twitter @rittal_ltd.
Rittal Ltd
- 01709 704000
- information@rittal.co.uk
- http://www.rittal.co.uk
- Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8QY GB
About us
Since its foundation in 1961, Rittal has continuously evolved into the world"s leading systems provider for enclosures, power distribution, climate control, IT infrastructure and software & services.
Today, "Rittal – The System." offers you a perfectly coordinated system platform. It unites innovative productions, pioneering engineering solutions and global service to accommodate the most diverse requirements. It caters to a whole host of industries, from machinery and plant engineering, to the automotive industry, through to information technology.All from a single source, all in top quality.
That is what "Rittal – The System. Faster – better – worldwide." is all about.
A workforce of 10,000 manufactures and develops "Rittal – The System." on your behalf. Ensuring you stay on track for success. Tap into synergy potential with our sister company Eplan, the leading manufacturer of software for cross-disciplinary engineering solutions.We never lose sight of our responsibility to the environment and society.
Where we supply to
Europe, Africa, Asia, Australia, South America, North America
Industries we supply to
Automation, Chemicals, Consultants, Components Electronics, Energy and Power, Food and Beverage, Glass Ceramics Cement, Metals and Minerals, OEM, Paper and Pulp, Pharmaceutical Cosmetics Toiletries, Plastics and Rubber, Recycling, Textiles, Tobacco, Water and Wastewater
-
Make wire processing ten times faster with Rittal’s Wire Terminal WT C: The versatile solution for wire processing
Rittal’s Wire Terminal WT C5 and C10 machines offer fully automatic wiring processes that go one step further. The innovative...
-
Smart cooling unit solutions with sustainable DNA Rittal Blue e+ S Cooling Units
Rittal is expanding its smart cooling unit solutions by adding the new Blue e+ S range. Our latest generation of...
-
Temperature vs Equipment – Who will Win?
Every year, there is a battle of two forces. The immovable object comes upon the unstoppable force in a war...
-
Experience Rittal live!
There are only weeks to go until the 2022 Drives & Controls exhibition which is held at the NEC Birmingham from the 5th-7th...
-
Rittal celebrates the one-millionth VX25
2021 was a triple milestone for Rittal, the company celebrated the 60th anniversary of its founding, the 75th birthday of...
-
Designing a Switchboard for a Fishing Trawler
When NU-Design Limited, a marine electrical services business based in Peterhead, Aberdeenshire, Scotland needed help in the designing of a very...
-
Support arm system
-
Smart Solutions for a changing world - Challenging the Edge
-
MAN VS MACHINE
